Basement Insulation

A basement sits partly or fully below grade, bordering soil at its walls and floor, which makes it a different kind of space than the rest of your home. Before Protect insulates a basement, we check it for moisture and identify any existing radon system components, since basements are where moisture problems and radon entry are both most likely to show up.

Reviewed by
General Manager
Basement insulation assessment A basement cutaway shows below-grade foundation walls, the floor framing above, and an existing radon vent pipe. Highlights identify moisture assessment, radon system components, and wall insulation.

What Basement Insulation Involves

Basement insulation typically means insulating the basement walls, the below-grade surfaces that border soil and tend to run colder than the rest of the home. The right approach depends on your basement's construction, moisture conditions, and whether it's finished, unfinished, or being finished as part of the project, which an assessment confirms before any material is scoped.

Water First and Radon-Aware: Why Basements Get Extra Attention

Water first.

Basements are one of the most common places in a home to find moisture problems, condensation on cold foundation walls, seasonal groundwater, or a history of water intrusion. Insulating over an active moisture problem in a basement can trap that moisture against the wall and encourage mold growth, so Protect addresses any active moisture issue first, coordinated with mold remediation and moisture control services where needed, before insulating.

Radon awareness.

A home's basement floor and walls are typically the primary way radon gas enters from the soil, through cracks, gaps, sump pits, and other foundation penetrations. Because of that, Protect's crews are trained to identify existing radon system components, such as vent pipes, sealed penetrations, and sump pit covers, and work around them when insulating basement walls, so your system continues to function as designed. Of all the insulation work Protect does, this is where that radon awareness matters most directly.

Stack effect.

The basement also sits at the lower end of your home's stack effect cycle, see our Air Sealing & Weatherization page for how warm air escaping upstairs pulls outside air in through the basement, crawl space, and rim joists.

Addressed the Right Way, in the Right Order

Moisture Assessed First

Active moisture or mold is resolved before any insulation is installed.

Radon-Aware Basement Work

Existing radon system components are identified and protected, since basements are the most common radon entry point in a home.

Works With Rim Joist as One System

The rim joist sits directly above the basement wall.

Our Basement Insulation Process

  1. Inspection and Assessment

    On-site inspection checking for moisture, existing insulation conditions, and any existing radon system components, before anything is scoped.

  2. Resolve Active Moisture

    Any active moisture or mold problem is addressed first, coordinated with mold remediation and moisture control services where needed.

  3. Insulate

    Basement walls are insulated to the scoped plan, with identified radon system components protected throughout.

  4. Document

    The completed work is documented.

Ready to Make Your Basement More Comfortable?

Request Service

Not Sure Yet? Start With an Assessment

Basement conditions vary widely from home to home. An assessment will confirm whether moisture needs to be addressed first, how the basement connects to your rim joist and crawl space, and what insulation approach fits your home, see our Crawl Space Insulation page for the related areas of the building envelope.

Learn More

The Protect Promise

Water First

We never insulate over an active moisture problem. Moisture and mold are resolved first, every time.

Radon-Aware Crews

Our crews are trained to identify and protect existing radon system components, especially important in basements, where radon most commonly enters a home.

Whole-Home Approach

We treat the basement as part of the connected building envelope, alongside the rim joist and crawl space above and around it.

Basement Insulation in Your Area

Basement insulation is currently available in Denver, CO and Salt Lake City, UT.

Frequently Asked Questions

Can you insulate a basement that has moisture problems?

No, not until the moisture is resolved. Protect addresses active moisture or mold issues first, often in coordination with mold remediation and moisture control services, before insulating basement walls.

Why does radon matter when insulating a basement?

Basement floors and walls are typically the primary way radon gas enters a home from the soil. Protect's crews identify existing radon system components, such as vent pipes, sealed penetrations, and sump pit covers, and work around them during basement insulation work.

How does basement insulation relate to rim joist insulation?

The rim joist sits directly above the basement wall, where the floor framing meets the foundation. The two areas are closely connected and often scoped as part of the same assessment.

What's the difference between basement and crawl space insulation?

Both are below-grade parts of the building envelope and share the same water-first principle, but a basement is typically a taller, more usable space, often finished or intended to be, while a crawl space is a shorter, unfinished area accessed differently. An assessment will confirm the right approach for each.

Should I insulate an unfinished basement?

It depends on your home's construction and moisture conditions, which an assessment will confirm. An unfinished basement isn't automatically ready for insulation if there's an active moisture issue to resolve first.

Talk to Protect Environmental About Basement Insulation

Request My Service

Find Your Local Office

What's Your Radon Risk?

Enter your zip code to learn about the radon levels near you.

what's your radon risk?